Connector Discussion

Discussion forum for the CAN-FIX protocol. This is a CANBus based communications protocol specifically suited for experimental aviation.

Moderators: John Nicol, birkelbach

birkelbach
Posts: 193
Joined: 04 Sep 2012, 14:42

Re: Connector Discussion

Post by birkelbach »

sprocket wrote: 1. Having two connectors to support CAN is unecessary and expensive because it may force custom tooled packaging.
2. A single 9-pin dsub can be edge mounted to a pcb, taking almost no area. Other types of connectors take more board area and are a pain to work with in the field. Dsubs are used everywhere and installation tools are cheap.
3. It is not necessary to have a pass-thru design. The networking and computer world abandonded this topology decades ago in favour of star architectures because of nasty fault multiplication issues.. The AXIS-9A is the wiring hub for this.
I agree that multiple connectors is bigger, more expensive, makes packaging difficult, etc. That's why I started this thread. I wanted to see if anybody thought that using a 15-pin instead of 2 9-pins made sense.

CAN is a multi-drop protocol. These designs are not really "pass-thru." The pins on the connectors are directly connected by traces on the PCB. I did this because it's very difficult to reliably solder/crimp more than one conductor onto most D-SUB connectors. It's not impossible, but are we not catering to beginners and experimenters? Maybe I'm wrong.

Multi-drop protocols are standard in the industrial controls business. Modbus, ControlNet, DeviceNet, Remote I/O, Profibus are all multi-drop. The industrial controls world doesn't like star configurations due to the single point of failure issues. Even Ethernet (a new player in this world) is being made to look more multi-drop. I would argue that our airplanes are more similar to the industrial controls world than to the computer networking world.

Part of the reason for using CAN in the first place is to be able to integrate multiple devices throughout the airplane with a minimum of wiring. A star topology does nothing to help with this. I don't see where the 'nasty fault multiplication issues' are.
4. I have complete a CAN design for the M-PWR-2. It alread adds substantially to the cost. Adding a second dsub 9 would require a larger package. As a result the BOM costs would double. That's a steep cost for a questionable feature.
I think the idea of a CAN based trim servo controller is awesome! It was a trim controller that gave me the idea to start working on CAN-FIX to start with. I guess I don't know what the "questionable feature" is?
Phil Birkelbach
Waller, Texas
RV-7 727WB
www.myrv7.com
birkelbach
Posts: 193
Joined: 04 Sep 2012, 14:42

Re: Connector Discussion

Post by birkelbach »

jeff54il wrote: The connector alone will probably weigh twice as much as the PCB and it has absolutely no IP protection whatsoever, not to mention RFI protection and the weight of the mating connector. So, my question: Does anybody know of a connector system similar to the dsub but using a 50-60 mil pitch? IP protection wouldn’t hurt either.
I've looked and the ones that I have found are expensive, difficult to get and/or require special tools. The most acceptable one that I have seen is the one that I referred to in a previous post. It uses a lot of board space and I'm not sure about the mechanical integrity of the mating connector.

I think in the grand scheme of things, the connectors and the PCBs are going to be a very small percentage of the weight. The real weight is in the wires. That 15-pin D-sub in the Tiny experiment probably weighs less than 6" of the wire connected to it. Spending a bunch of money to shave a few grams off of the weight may not be worth it. D-subs are cheap because they are ubiquitous. As ugly and old as they are it's hard to fight them because they are everywhere and they work well.
Phil Birkelbach
Waller, Texas
RV-7 727WB
www.myrv7.com
sprocket
Posts: 40
Joined: 28 Oct 2012, 23:09

Re: Connector Discussion

Post by sprocket »

It's the second connector that adds cost and decreases network reliability. It's not a problem for small networks, but the connectors are the largest components on the pcb, so why carry the extra cost, which can also push you out of standard packages.

V
V e r n
Post Reply